Kitchen and Bathroom Electrical Wiring Gfci Electrical Circuit Wiring – Bathrooms and Kitchen Areas Require Special Electrical Wiring -
Kitchen and Bath Areas
GFCI Electrical Wiring
Remodeling Wiring for Kitchens and Baths
Remodeling Wiring for Kitchens and Baths
Kitchens and Bath areas require special electricity wiring for electrical outlets.
The electrical outlet locations are also much different than in other portions of homes.
What are electrical requirements for kitchen and bath areas?
As electrical requirements change frequently be sure to check with your certified local electrician for any special requirements you and questions for your kitchen or bath remodeling. This a summary of a few of the guidelines from the national electrical code a few years back.
In the kitchen area the NEC requires no more than 6 fee from a given location to be from an outlet which would make the outlets no more than 12 feet apart with special outlet locations in the kitchen area or over counter-tops.
Counter-top receptacles in your kitchen must be served by two or more different circuits. Each kitchen counter space that is wider than 12 inches must have its own outlet, with no point along than countertop being more than 24 inches apart horizontally or 48″ of space between the outlets in the kitchen.
Often electricians run a three wire 240 volt cable from the service panel and provide two new 120 volt circuits. One side of each receptacle is served by one of the circuits while the other side is served by the other circuit, giving two circuits available at each outlet which gives the term split circuit. Protection for over-current on a split circuit used a double breaker which is linked in the circuit’s panel.
Ensuring kitchen and bathroom safety, the NEC requires GFCI protection in all new bathrooms, and in kitchen outlets within six feet of the kitchen’s sink and other locations around the house. Adding ground fault protection to existing circuits makes sense in any bathroom or kitchen.
A “ground Fault” is a current leak caused by faulty electrical insulation in a tool or appliance which is plugged in. This current leak may be too small to trip a circuit breaker for your kitchen or bath area, yet can prove fatal to anyone standing on a wet floor or touching a grounded metal plumbing fixture for an example.
There are three GFCI types. One is a circuit breaker installed in the main panel. A second type of GFCI outlet is installed in the outlet box as a replacement for an existing outlet, and there also is a simple plug in GFCI outlet or extension cord. Installing a feed through GFCI outlet is the most common for kitchen and bath areas with more than one outlet. A feed through GFCI allows ground fault protection to all of the receptacles beyond the outlet in the same circuit.
Although adding GFI outlets is very simple step when remodeling kitchen or bathrooms ]people wanting to do work them selves too often make the fatal mistake of missing the minor addition of the correct type of outlet. Be sure to understand this step, or hire an electrician to make sure your kitchen and bathroom areas have the right gauge electrical wiring at the right spacing apart, and at very least ensure your circuits in areas such as Kitchens and baths where moisture can be present is protected with a GFI style of outlet.
We hope this helps as you start your new kitchen planning and kitchen remodel. Please let us know what information you were looking for on our website does not have the content you are looking for so we can be sure to include it in the future – Thank You!
Kitchen and Bath Areas
GFCI Electrical Wiring
Remodeling Wiring for Kitchens and Baths
Kitchen and Bathroom Remodeling Circuits and Wiring
Watch the video related to kitchen remodeling
Burt and Mabel agree to go forward with their kitchen remodel under one condition – Burt gets to choose the contractor. But is Shady McShade a licensed and trustworthy contractor? And is Boris Beasley as sinister as his record indicates? Need help finding a contractor for your job? Visit www.ServiceMagic.com
Help answer the question about kitchen remodeling
How do you know if you're paying too much for kitchen remodeling labor?Is there a formula for figuring this out? We know exactly how much our materials will cost (appliances, tile, cabinets, etc.) but have no idea what to expect when they give us an estimate for labor. Any help would be appreciated!
Related Post
Tags: Electrical Circuits, Electrical Outlet, Electrical Wiring for Kitchen and Bathrooms, Electrical Wirings, Electricity Wiring, GFCI, Ground Fault Circuit Interupters, Kitchen and Bath Electrical, Kitchen Bathroom Wiring, remodeling, Remodeling Wiring Kitchens and Baths
I don't exactly how much it costs, but I can't say it's cheap. Going over budget is a common situation also. Depending on the region you're in, the wiring/lighting additions you'll need, the company you hire, and the materials you choose to use, this could add up to a large investment. The cost can range from sensible prices to outrageously expensive prices all depending on the choices you make.
Just think about what you would like to do to your kitchen and call some companies and ask them for an estimate.
Is this the house you really want? If so, enjoy your house!
Good Luck!!
Try:
http://www.kitchen-bath.com/kbb/index.jsp
http://www.searshomeimprovements.com/ProductOffer2.aspx?o=4&t=103
http://www.hometime.com/Howto/projects/kitchen/kitchen_1.htm
http://www.hometime.com/Howto/projects/kitchen/kitchen_1.htm
Try searching using: kitchen remodeling, kitchen remodeling ideas, kitchen remodeling pictures
Have fun, it a great project!!!!!
I agree, the pale yellow sounds nice. But if the color concerns you, try a pale yellow with a bit more earthy brown tones in it. When you look at your paint samples, you will see the pure yellows that are crisp in color and you will see the more muted yellows. Try out a couple of the more muted yellows.
Also, go ahead and collect samples of what you want to eventually do in your home, like the granite color. This will help to cordinate everything as you go.
Also the paint stores sell small quart and smaller samples of paint that you can test out colors to see if you like them. I love these. You can buy several colors, paint them side, by side and then make a final decision.
If the ceiling above is insulated, you cannot use non-IC rated cans. Other than that, most light fixtures are allowed. Hope this helps.
If you want ideas on kitchen cabinets, go to http://www.kraftmaid.com. If you click on Help and Information, then you can click on Order Literature at the left. Kitchen counters, try http://www.corian.com – you can get a free catalog in the mail if you fill out the form on the contact us page and uncheck the section that says send me info by e-mail. Otherwise, they'll just e-mail it to you. As far as decorating schemes, I find a lot of good information on http://www.HGTV.com. Good luck. I'm in the planning stages of a kitchen remodel myself.
Most electrical contractors charge a minimum of $350-$600 per job. If the electrical breaker box is near the kitchen then the minimum charge may cover the whole job. If wires need to be run a long way to get to the kitchen, then the charge could be much more.
It took 3 months….. we did it ourselves and it cost 27,000$ Canadian….
Unexpected expenses: wiring that was no longer any good, having to buy more tiles, redoing the floor base to make it smooth for the new tiles (because pulling up the old ones ruined the floor underneath) and having to make a new countertop instead of just being able to relaminate the old one (the wood underneath the old laminate was rotting).
Yes… very happy with the outcome! We have just sold the house… paid it 133 500.00$ just over 5 years ago…. just sold it for 279 500.00$… I'd say that definitely covers the cost of the kitchen renovation!
We are a well established full service from design to construction to installation kitchen and closet company, 15 years. Our contracts are 50% deposit (covers Material cost), 40% on first day of installation (when materials are all in the building) and 10% upon completion of job and customers sign off on all punch list and walk through.
The final moneys are basically our profit, so that are incentive to complete in a timely matter. Our contracts are non negotiable, except for our clients that are builders and designers that are repeat business. Usually customers get un easy about the deposit, but we do provide a packet, that includes how long we have been around, our BBB report and our licensing with years licensed shown.
That is our policy and is almost standard with some exceptions.
Actually there are several types of sinks available these days. The design and layouts of the sinks can come in a wide range of patterns to meet anyone's needs. Deep and wide, to shallow and oblong, you can find just about anything.
What the sinks are made of is almost a design question. Obviously most people want something durable, while others simply want something new and plan on selling soon. Either way, here are some examples of the type of sinks commonly available to the public.
Solid surface material sinks, ones that are made of the same material as the countertops, are good durable sinks and look nice as part of the overall countertop. There are also acrylic sinks available. Both are good choices when a specific color is wanted, say in a retro theme, unfortunately, they both scratch and fade from cleaning over time, because they are, after all, basically plastic. If you're careful and try not to use abrasive cleaners, they can last a lot longer.
Stainless steel sinks are also available in many patterns and sheens. Some of them are quite nice and very durable and probably the best option from a strictly utilitarian perspective. I am not sure about them because they fade over time and that "new" shine never truly comes back like it did in the store. They tend to be noisy too because they are relatively thin compared to some other types of sinks.
Another type of sink that is available is the enamel on steel. These sinks are basically a steel bowl with hard enamel baked onto it. They are good sinks, but like one writer stated, they can be prone to chipping quite easily. They too have a very long life if well cared for.
In my humble opinion, the best sink to consider for the kitchen is the cast iron. These sinks are cast iron and are coated with an enamel type surface and although they can be heavy, they are durable, make no noise, don’t chip or scratch and take a beating and come out shiny and clean with ANY cleaner. For my money, my tastes and my needs, these are the best sinks. For the bathrooms, I would stick to the vitreous china sinks because they are just as durable and nice as the cast kitchen sinks.